Smart Ring Not Syncing With Health Connect? 9 Fixes

If your RingConn data appears normally inside the RingConn App but is missing from Health Connect, the smart ring itself may be working correctly.

The problem is more likely somewhere later in the data chain: RingConn may not have permission to write a particular data type, Android may be restricting background work, Health Connect may not support the metric you expect, or another App may not have permission to read the stored records.

The most useful troubleshooting strategy is to follow the data in order:

RingConn ring → RingConn App → Health Connect → destination App

Once you identify where the data disappears, you can fix that specific layer instead of repeatedly reinstalling Apps or resetting the ring.

Quick Answer: Why Is RingConn Not Syncing With Health Connect?

Common causes include:

The ring has not finished syncing with the RingConn App.
RingConn does not have permission to write the missing data type.
The data type is not currently supported by RingConn's Health Connect integration.
Android is restricting RingConn's background activity.
The RingConn App, Android, or Health Connect needs an update.
The record has reached Health Connect but the destination App cannot read it.
Several Apps are contributing the same category and Health Connect is applying source-priority rules.

Start with four checks:

Confirm that the missing data appears inside the RingConn App.
Confirm that RingConn has Health Connect permission for that data type.
Check whether the record actually exists inside Health Connect.
If it does, check the destination App rather than troubleshooting the ring again.

Understand the RingConn-to-Health-Connect Data Chain

Stage	What Happens	Typical Failure
1. Ring → RingConn App	The ring transfers stored sensor data to the phone through Bluetooth	Bluetooth, battery, distance, App connection, or unfinished synchronization
2. RingConn App processing	RingConn processes supported sleep, activity, and physiological records	The report has not finished processing yet
3. RingConn App → Health Connect	RingConn writes authorized supported data types into Health Connect	Permission missing, unsupported metric, or background restriction
4. Health Connect storage	Health Connect stores the shared records on the Android device	The expected record was never written
5. Health Connect → another App	An authorized App reads records from Health Connect	Read permission, refresh schedule, source rules, or App-specific display logic

Health Connect does not communicate directly with the RingConn ring.

The RingConn App remains the primary source for RingConn-specific sleep reports, HRV, stress, recovery information, scores, and other proprietary insights.

First Identify Where the Sync Is Broken

What You See	Most Likely Problem Area
No new data inside RingConn	Ring-to-phone synchronization
Data is in RingConn but not Health Connect	RingConn Health Connect permission, supported data type, or write process
Data is in Health Connect but not another App	Destination App permission or refresh behavior
Steps sync but sleep does not	Sleep processing or sleep-specific Health Connect permission
Everything syncs except HRV	Current RingConn Health Connect limitation rather than a broken connection
Data appears mainly after opening RingConn	Possible Android background restriction or normal delayed processing
Totals look unexpectedly high	Several Apps may be contributing the same category

Check Whether Your Android Version Supports Health Connect

Health Connect behaves differently depending on your Android version.

Android 14 and Later

Health Connect is integrated into the Android system.

A common path is:

Settings → Security & Privacy → Privacy Controls → Health Connect

You can also search for Health Connect inside Android Settings.

Android 13 and Earlier

Health Connect is not built into the Android framework on these versions and generally needs to be installed separately from Google Play.

A common path after installation is:

Settings → Apps → Health Connect

Health Connect itself requires Android 9 or later. Menu names may vary by phone manufacturer and operating-system version.

How to Connect RingConn to Health Connect

Begin the integration from RingConn rather than relying only on the Health Connect settings screen.

Update the RingConn App.
Open RingConn.
Go to Me.
Open Data Management.
Select Connect to Health Connect.
Tap Sync to Health Connect.
Review the Health Connect permission request.
Authorize the specific categories you want RingConn to share.

For the current setup flow and supported categories, review the official RingConn Health Connect guide.

Fix 1: Make Sure the Ring Has Synced With RingConn First

Health Connect cannot receive records that have not yet reached the RingConn App.

Before changing Health Connect settings:

Turn on Bluetooth.
Keep the ring near the phone.
Open the RingConn App.
Wait until the ring appears connected.
Allow pending synchronization to finish.
Confirm that the expected data appears inside RingConn.

If the RingConn App itself is missing the sleep session, heart-rate data, steps, or SpO2 record, troubleshoot the ring-to-phone connection first.

Health Connect cannot recreate data that RingConn has not collected or processed.

Fix 2: Check Whether the Missing Data Type Is Actually Supported

Not every metric available inside RingConn is currently exported to Health Connect.

RingConn's current Health Connect documentation lists the following supported categories:

Category	Current RingConn Health Connect Data
Activity	Resting energy, steps, exercise calories
Sleep	Time in bed, awake duration, sleep stages
Heart Rate	Resting heart rate, average heart rate
Blood Oxygen	SpO2
Body Measurements	Height, weight

Other RingConn-specific scores, interpretations, charts, or health insights may remain available only inside the RingConn App.

What About HRV?

RingConn currently states that HRV synchronization to Health Connect is not supported because of an algorithm compatibility issue.

If HRV is missing while supported metrics such as steps, sleep, heart rate, or SpO2 are transferring correctly, repeatedly resetting Health Connect permissions will not solve the HRV limitation.

Continue reviewing HRV inside the RingConn App unless RingConn announces updated integration support.

Fix 3: Review RingConn's Health Connect Permissions

A Health Connect connection can exist while one individual category remains unauthorized.

Open Health Connect and go to:

Permissions and data → App permissions → RingConn

Review the categories RingConn is allowed to access or write.

For example:

Steps present but sleep missing → review sleep permission.
Sleep present but SpO2 missing → review blood oxygen permission.
Nothing is being written → confirm RingConn has active Health Connect access.

Grant only the data permissions you actually want to share.

Revoking an App's Health Connect permission does not automatically delete health records that are already stored in Health Connect.

Fix 4: Disconnect and Reconnect the Integration

After an Android update, phone migration, App update, or interrupted setup, the Health Connect authorization can occasionally need to be recreated.

If supported data still does not transfer:

Open Health Connect.
Go to App permissions.
Select RingConn.
Revoke the relevant access.
Close Health Connect.
Open the RingConn App.
Return to Me → Data Management → Connect to Health Connect.
Start the authorization flow again.
Select the categories you want to share.
Test using newly collected data.

RingConn Smart Ring

Do not clear Health Connect storage as a routine troubleshooting step. Revoking App permission and reconnecting is much less destructive.

Fix 5: Check Android Background and Battery Restrictions

Android can restrict how frequently Apps perform background work.

A particularly important setting is the App's battery-use mode.

A common path is:

Settings → Apps → RingConn → Battery

Depending on the phone, you may see options such as:

Unrestricted
Optimized
Restricted

Optimized is the normal Android default on many devices and does not automatically mean something is wrong.

Restricted can prevent or significantly delay background jobs and should be reviewed when RingConn stops syncing unless you manually open the App.

When to Test Unrestricted Mode

Consider temporarily testing Unrestricted or the equivalent manufacturer setting when:

New data reliably appears only after you open RingConn.
The App is repeatedly placed into a Deep Sleep or restricted list.
Background synchronization stops after the screen has been off for a long period.
The problem disappears while RingConn remains open in the foreground.

If this solves the issue, decide whether the improvement is worth the potential additional battery use.

Phone manufacturers can add their own battery-management layers, so the exact labels vary between Samsung, Pixel, Xiaomi, OnePlus, and other Android devices.

Fix 6: Check Background Data and Unused-App Settings

Battery mode is not the only setting that can interfere with background behavior.

Depending on your phone, also review:

Background data
Background activity
Data Saver exceptions
Pause App Activity if Unused
Unused Apps
Deep Sleep or Sleeping Apps lists

Android can revoke permissions and stop background activity for Apps categorized as unused.

If you rely on automatic RingConn-to-Health-Connect sharing, make sure RingConn has not been unintentionally placed into one of these restricted states.

Fix 7: Allow Sleep Reports to Finish Processing

Different data types do not necessarily become available at the same speed.

Steps can accumulate throughout the day, while sleep information depends on a completed overnight session and subsequent processing.

The sequence can be:

The ring transfers overnight data to RingConn.
RingConn processes the sleep session.
Supported sleep records are written to Health Connect.
A destination App reads those records.

This is why steps can appear before sleep even when all permissions are configured correctly.

If Steps Sync but Sleep Does Not

Confirm that the complete sleep report exists inside RingConn.
Wait for processing to finish.
Check RingConn's sleep permission in Health Connect.
Open Health Connect and inspect the Sleep category.
Check the destination App's sleep read permission.
Refresh the destination App.

For a broader explanation of the RingConn data flow, see the RingConn data synchronization guide.

Fix 8: Use Health Connect Recent Access to Find the Broken Layer

Health Connect can show which Apps recently accessed the platform.

Open Health Connect and review Recent Access.

You can use this as a troubleshooting clue:

What Recent Access Shows	What It Suggests
No recent RingConn activity	Check RingConn authorization, supported data types, and native App synchronization
RingConn accessed Health Connect but the destination App did not	Check the destination App's permissions and refresh behavior
Both Apps accessed Health Connect	The issue may be App processing, display logic, timing, or unsupported fields

For a more direct check, browse the relevant Health Connect category and inspect the stored entries.

If the record exists in Health Connect, the ring and RingConn App have already completed the important upstream part of the transfer.

Fix 9: Update and Restart Before Reinstalling Anything

Keep destructive troubleshooting near the end of the process.

Check for updates to:

RingConn App
Ring firmware
Android
Health Connect where it is distributed as an App
The destination health or fitness App

Then:

Restart the phone.
Enable Bluetooth.
Open RingConn.
Complete a full ring synchronization.
Confirm the native RingConn data is present.
Review Health Connect permissions.
Test a newly collected supported record.

Do not begin by factory resetting the ring, clearing Health Connect storage, or deleting your RingConn account.

If RingConn already contains the correct data, re-pairing the physical ring is unlikely to fix a problem that exists only between RingConn and Health Connect.

RingConn Smart Ring

Why Does RingConn Sync Only When I Open the App?

This pattern can indicate that pending ring data or Health Connect writes are not completing reliably in the background.

Review:

RingConn's battery-use state
Whether the App is marked Restricted
Manufacturer-specific Deep Sleep settings
Background activity settings
Background data
Unused-App permission removal

Also remember that intentionally opening RingConn after waking can still be a useful daily habit because it confirms that overnight ring data has transferred and sleep processing has completed.

Not every delay is necessarily a malfunction.

Why Is Data in Health Connect but Missing From Another App?

If the record is visible inside Health Connect, RingConn has already written the data successfully.

The next step is the destination App.

Open:

Health Connect → Permissions and data → App permissions → [Destination App]

Confirm that the App has read permission for the relevant category.

Then open the destination App and refresh it if necessary.

Different Apps can:

Read Health Connect on different schedules.
Ignore data types they do not support.
Display only selected portions of a record.
Combine Health Connect records with their own information.
Apply their own date or aggregation rules.

Once data is inside Health Connect, further display differences are no longer necessarily a RingConn synchronization problem.

Check Health Connect Data Sources and Priority

Multiple Apps can contribute the same type of health or activity data.

Health Connect lets you control which source has priority when overlapping records conflict.

The current path is:

Health Connect → Permissions and data → Manage Data → Data sources and priority

Here you can:

See which Apps contribute to a category.
Add or remove sources from calculated totals.
Reorder the source priority.
Confirm whether RingConn is contributing records.

When two Apps write overlapping step records, Health Connect can use the higher-priority source for the conflicting period rather than simply adding every value together.

Some destination Apps may still choose to read and combine records differently, so check the destination App as well when totals remain unexpected.

Do Not Confuse Source Priority With Write Permission

These settings solve different problems.

Setting	What It Controls
App permission	Whether RingConn or another App may read or write a particular Health Connect data type
Data source inclusion	Whether a source contributes to Health Connect's category totals
Source priority	Which source is preferred when overlapping records conflict

Changing priority cannot fix a category that RingConn never had permission to write.

A Five-Minute Troubleshooting Flow

If you want the shortest possible process, use this sequence.

1. Open RingConn

Is the missing data there?

No: troubleshoot the ring, Bluetooth, battery, and RingConn sync.
Yes: continue.

2. Check Whether RingConn Supports That Metric in Health Connect

Unsupported: use RingConn instead.
Supported: continue.

3. Check RingConn's Health Connect Permission

Off: authorize it.
On: continue.

4. Look for the Record Inside Health Connect

Missing: reconnect the integration and review Android background restrictions.
Present: RingConn has completed its part.

5. Check the Destination App

Review read permission, Recent Access, source priority, and the destination App's own refresh behavior.

Health Connect Sync Decision Matrix

Problem	Most Useful First Check
No RingConn data at all	Bluetooth and native RingConn synchronization
RingConn has data, Health Connect does not	Supported type + RingConn write permission
Only HRV is missing	Current integration limitation; use RingConn App
Steps sync, sleep does not	Sleep processing + sleep permission
Health Connect has data, another App does not	Destination App read permission
Sync occurs mainly when RingConn is opened	Background/battery restriction
Totals are unexpectedly high or inconsistent	Data sources and priority
Problem started after an update	Update all components, restart, and reconnect Health Connect

Android Settings Checklist

Setting	What to Verify
Bluetooth	Available while synchronizing the ring with RingConn
Nearby Devices	Allowed when requested by RingConn
RingConn Health Connect access	Enabled for the supported categories you want to share
Battery use	RingConn is not unintentionally set to Restricted
Background activity	Not disabled by manufacturer-specific power management
Background data	Available when needed
Unused-App management	RingConn permissions are not being automatically removed
Recent Access	Check whether RingConn and the destination App recently accessed Health Connect
Data source priority	Review when several Apps write the same category
Software	RingConn App, firmware, Android, Health Connect, and destination App are current

RingConn Models and Health Connect

Current RingConn models use the RingConn App as their primary data and insight environment, with Health Connect providing optional sharing of supported Android health categories.

Model	Primary RingConn Experience	Health Connect Role
RingConn Gen 3	Broad health insights, Vascular Health Insights, Smart Vibration Alerts, sleep, activity, and wellness tracking	Shares supported standardized categories with compatible Android Apps
RingConn Gen 2	Sleep, recovery, SpO2, HRV, activity, and Sleep Apnea Pattern Insights	Shares supported activity, sleep, heart-rate, SpO2, and body-measurement categories
RingConn Gen 2 Air	Core sleep, activity, stress, and everyday wellness tracking	Uses the same RingConn-to-Health-Connect sharing workflow for supported categories

Explore RingConn Gen 3 if you want the broadest current RingConn health experience, including advanced insights, vibration alerts, long battery life, and a universal charging case.

Choose RingConn Gen 2 if your priorities include sleep, recovery, Sleep Apnea Pattern Insights, and a thin titanium design.

Consider RingConn Gen 2 Air if you want core sleep, activity, stress, and wellness tracking in a stainless-steel design.

When Should You Contact RingConn Support?

Consider contacting Support when:

The ring itself will not synchronize with RingConn.
RingConn does not appear in Health Connect after the official authorization flow.
Permissions repeatedly disappear immediately after being granted.
A currently supported data type remains missing across several new records.
RingConn repeatedly crashes during Health Connect authorization.
The problem began after an update and continues after restarting and reconnecting.

Useful information to prepare includes:

Phone model
Android version
RingConn App version
Ring firmware version
The specific missing data type
Whether the record appears in RingConn
Whether it appears inside Health Connect
Screenshots of RingConn's Health Connect permissions
Recent Access information
Battery/background setting screenshots when relevant

Final Takeaway: Troubleshoot the Data Chain, Not Everything at Once

If RingConn is not syncing correctly with Health Connect, use the data chain to locate the problem:

Ring → RingConn App → Health Connect → Destination App

If the data is missing from RingConn itself, focus on Bluetooth, ring battery, and native RingConn synchronization.

If the data exists in RingConn but not Health Connect, confirm that the metric is supported, review RingConn's Health Connect permission, and check Android background restrictions.

If the record already exists in Health Connect, RingConn has completed the write process. Troubleshoot the destination App's read permission, refresh behavior, and data-source handling instead.

Remember that not every RingConn metric is exported. RingConn currently supports Health Connect sharing for selected activity, sleep, heart-rate, SpO2, height, and weight information, while HRV remains available primarily inside the RingConn App rather than through the current Health Connect integration.

Avoid destructive troubleshooting such as factory resetting the ring, deleting your account, or clearing Health Connect storage unless there is a specific reason to do so.

RingConn products are not medical devices and are not intended to diagnose, treat, cure, or prevent any disease. Health and wellness data should be used for personal reference and should not replace professional medical advice, diagnosis, or treatment.

FAQ: RingConn and Health Connect Sync

Why is my RingConn data not appearing in Health Connect?

First confirm that the data exists inside the RingConn App. Then check whether the metric is supported by RingConn's Health Connect integration and whether RingConn has permission to write that category.

Why does RingConn sync only when I open the App?

The App may be completing pending ring synchronization or Health Connect writes only when it becomes active. Check whether Android has placed RingConn in a Restricted, Deep Sleep, or other aggressive background-limiting state.

Why do steps sync but sleep does not?

Sleep data usually needs a complete processed sleep session before it can be shared. Confirm that the sleep report is finished inside RingConn, then check RingConn's Health Connect sleep permission.

Does RingConn currently sync HRV to Health Connect?

No. RingConn currently states that HRV synchronization through Health Connect is not supported because of an algorithm compatibility issue. Continue reviewing HRV inside the RingConn App.

Why is data visible in Health Connect but missing from another App?

If the record already exists inside Health Connect, check the destination App's Health Connect read permission, refresh behavior, and support for that specific data type.

Should I set RingConn battery use to Unrestricted?

Not necessarily for every user. First make sure RingConn is not set to Restricted. If synchronization repeatedly works only while the App is open, testing Unrestricted or the equivalent manufacturer setting can help determine whether background battery restrictions are causing the problem.

Should I clear Health Connect storage or reset my ring?

Not as an early troubleshooting step. Start with native RingConn synchronization, supported data types, permissions, Recent Access, background settings, and reconnecting the Health Connect integration. Clearing storage or resetting the ring can create unnecessary data or setup problems.